Weighing Indicator Controller with up to 16 Set Points (ADW-SP16)
- Up to 16 setpoints, each with an associated SPCO relay (on DIN rail module)
- Individual set point, In-flight & hysterisis values
- Programmable from the ADW keypad
- Relay contact rating 230V @ 5A AC
- Communications and Printer Driver
- Simple one pass auto calibration for minimum set-up time on site
- Provides excitation of 10V @ 160mA to drive up to 6 x 350 Ohm load cells
- Variable gain input sensitivity from 0.5 to 200 mV/V
- 6 wire input to compensate for zener barrier and cable losses
- RS232 or RS485 communications for setup, data transfer or label/ticket printing
The DIN rail mounted remote relay units offer an increased number of set points over that provided by a standard ADW15 strain gauge indicator/controller.
This allows for multi action operations such as batch and recipe control.
The software of the ADW-SP16 gives the user freedom to program the number of set points for their requirements. A single ADW-SP16 will control up to 16 set points, programmed from its front panel.
Set points can be individually set up with In Flight compensation and hysteresis values.
Separate 'Output Latch' and 'Output Action' for up to 14 of the 16 set points is available, settable from the front panel of the ADW-SP16. A special mnemonic allows the user to specify the number of set points to be used.
All relays are pluggable and connections are made via field screw terminals.
| Inputs | |
|---|---|
| Calibration | Automatic digital by use of keypad and 1 (or 2) known weights. Manual calibration can also be selected |
| Auto Tare | By pressing keys ' > ' and then 'R' , display will zero. Auto tare value can also be viewed and manually changed if required. Auto tare value is retained on powerdown. |
| Sensitivity | Preset via DIL switches between 0.5 to 200mV/V |
| Excitation | 10V DC nominal, 150mA maximum |
| Compensation | By ± sense wires to compensate for cable, connection volt drops and any variation in 10V supply |
| Accuracy | 90 days ± 0.08% of reading ± 0.05% of FS typical |
| Drift | 0.002%ºC typical @ 2.5mV/V |
| DC Analogue Outputs | |
| DC Voltage | 0 to 5V, 0 to 10V, -10 to +10V, Max Current out 50mA |
| DC Current | 0 to 1mA, 0 to 20mA, 4 to 20mA, Max Voltage out 20mA |
| Accuracy | typical ± 0.08% of output, ± 0.08%FSD |
| Resolution | as display resolution, max 15 bits |
| Calibration | by 15-turn pre sets for gain and offset |
| Inversion | By keypad value |
| Isolation | ±130V RMS or DC max to analogue input or to any other port |
| Ranging | Fully keypad scalable over desired display range |
| PID | Power level, when selected = 12 bit resolution output |
| The Relay Output Module | |
| The module consists of 8 relays rated at 230 volts 5 Amps - SPCO, Alarm via 30V 50mA NC contact, DIN rail mounted for a G or top hat profile. Each relay is plug-able and connections are made by 2.5mm field screw terminals. Indication of relay status is shown by LED's. Trip points volt free contact. The module can be situated up to 2 metres from the ADW15 load cell indicator controller. |
|
| Communication Port CP Operation | |
| All display data can be accessed via the communications port along with relay, PID power and EEPROM status. All user configurable data can be changed including EEPROM enable/disable and relay reset. | |
| Type | Details |
| RS485/422 | For up to 32 instruments on 1 bus, 4 wire, Protocol supports up to 254 |
| RS232 | For up to 25 instruments per interface, 4 wire |
| Cable Length | 1km (depending on baud rate) |
| Baud Rates | 300, 600, 1200, 2400, 4800, 9600 (19200 MANTRABUS only) |
| Electrical Isolation | ±130V RMS or DC max to analogue input or any other port |
| Formats | MODBUS RTU, MANTRABUS and printer output formats |
| Power Supplies | |
| 220V-230V AC 50-60Hz 10W, 110V-120V AC 50-60Hz 10W, 9-32V DC 10W isolated | |
| Base ADW15 | |
| Displays | 7 segment LED 4.5 digit 10mm.3 x 3mm LED's 2 for relay status, 1 for program and hold indication |
| Controls | |
| 4 membrane panel keys with tactile feedback. 1 scroll key to view/update parameter. 1 digit select key. 1 digit increment key. 1 reset key. Keypad disable by internal links behind front panel. Hold function by digit select key when in input mode. | |
| Data Retention/Protection | |
| Retention | 10 years for set up values, minimum of 100,000 write cycles. |
| Protection of Data and Function(s) | Watchdog timer giving repeat auto resets. Impending power detection and hold off. Keypad security and time out. |
| Environmental | |
| Storage Temperature | -20 to +70ºC |
| Operating Temperature | -10 to 50ºC |
| Relative Humidity | 95% maximum non condensing |
| CE Environmental Approvals | European EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC |
.jpg)
Documents
Software
Product order options
Please read the following before selecting the options for this product:
ADW15 fitted with Special Edition 16 Set Point Software with remote Driver MOdule to operate 4,8,12, or 16 relay remote DIN Rail mounted modules as required.
Starting with the base model ADW-SP16, select the options that you need to configure the device to meet your needs.
| Base Unit | Code |
|---|---|
| ADW-SP16 Multiple Set Point Controller | ADW-SP16 |
| Outputs | Code |
| Analogue Output 0-5V | V02 |
| Analogue Output 0-10V | V04 |
| Analogue Output 0-1mA | A01 |
| Analogue Output 0-20mA | A02 |
| Analogue Output 4-20mA | A03 |
| Comms | Code |
| RS485/232 Comms Module | COM 1 |
| Serial Port | S01 |
| Power Supplies | Code |
| Power Supply 110V AC | W110 |
| Power Supply 240V AC | W240 |
| Power Supply 12/24V DC | W12/24 |
| Mounting | Code |
| Panel Mount | P |
| Din Rail Mounting | D |
| Accessories | Code |
| Din Rail Mounted 8 Relay Module | REM8 |
| Din Rail Mounted 4 Relay Module | REM4 |
| Remote PSU (Required for 4+ Relays) | REM PSU |
| REM Interconnection Lead | REMC2 |
| VisualLink SCADA Software Full Version (Ex Works) | VLA |
| VisualLink Runtime Key (Ex Works) | VLR |
| VisualLink Runtime Key USB (Ex Works) | VLRU |
| VisualLink Runtime Software Key (Ex Works) | VLS |
| VisualLink SCADA Software Demo | VLD |
Batch Weighing Controller, 12 Ingredients or Components
Weighing Indicator/Controller for Loss in Weight
