Panel Mount Weighing Indicator and Controller (ADW15)

In Stock

Volume Prices Available

Direct Strain Gauge input 4.5 digit resolution
Variable sensitivity from 0.5 to 200mV/V
Excitation 10V 160mA to drive up to 4 load cells
6 wire input to compensate for zener barrier and cable losses
Simple one pass auto calibration for minimum set-up time on site
Auto tare and peak hold actioned by volt-free contacts
Fully isolated 4-20mA and 0-10V analog outputs
RS232 or RS485 communications for setup, data transfer or label/ticket printing
Programmable in-flight compensation for dynamic weighing operations
AC or DC power supply options

Introduction
Specifications
Dimensions
Downloads
Order Information
Related Products

The ADW15 Weighing Indicator / Controller is a very flexible digital load cell indicator and display system in a panel mount format, optimised for single or multiple load cell and weighing applications. The digital architecture offers very easy one-pass calibration and fast setup. This versatile amplifier panel meter offers options of isolated analogue outputs, latching relays or digital outputs for control or alarm functions. The RS232 or RS485 options provide for digital communications (including setup) and can support label or ticket printers. For a wall or surface mount version, see model SMW Weighing Indicator / Controller, and for a wireless radio version, see our range of T24 Radio Telemetry Display Modules.

Inputs
Calibration	Automatic digital by use of keypad and 1 (or 2) known weights. Manual calibration can also be selected
Auto Tare	By pressing keys '>' and then 'R' display will zero. Auto tare value can also be viewed and manually changed if required. Auto tare value is retained on powerdown.
Sensitivity	Preset via DIL switches between 0.5 to 200mV/V
Excitation	10V DC nominal, 150mA maximum
Compensation	By ± sense wires to compensate for cable, connection volt drops and any variation in 10V supply
Accuracy	90 days ± 0.08% of reading ± 0.05% of FS typical
Drift	0.002%ºC typical @ 2.5mV/V
DC Analogue Outputs
DC Voltage	0 to 5V, 0 to 10V, -10 to +10V, Max Current out 50mA
DC Current	0 to 1mA, 0 to 20mA, 4 to 20mA, Max Current out 50mA
Accuracy	typical ± 0.08% of output, ± 0.08%FSD
Resolution	as display resolution, max 15 bits
Calibration	by 15-turn pre sets for gain and offset
Inversion	By keypad value
Isolation	±130V RMS or DC max to analogue input or to any other port
Ranging	Fully keypad scalable over desired display range
PID	Power level, when selected = 12 bit resolution output
Communication Port CP Operation
All display data can be accessed via the communications port along with relay, PID power and EEPROM status. All user configurable data can be changed including EEPROM enable/disable and relay reset (address code cannot be changed).
Type	Details
RS485/422	For up to 32 instruments on 1 bus, 4 wire
20mA	For up to 25 instruments per interface, 4 wire
Cable Length	1km (depending on baud rate)
Baud Rates	300, 600, 1200, 2400, 4800, 9600 (19200 MANTRABUS only)
Electrical Isolation	±130V RMS or DC max to analogue input or any other port
Formats	MANTRABUS and printer output
Alarm/Control Outputs
SPCO	1 relay on SP1, 2 relays on SP1& 2
DPCO	1 relay on SP1
Relays	230V at 5A AC resistive
Isolation	±130V RMS
Keypad Programmable Options	Hysteresis, Latching, Output Inversion, Delay Times, PID values and Time Proportioning.
Power Supplies
220V-230V AC 50-60Hz 10W, 110V-120V AC 50-60Hz 10W, 9-32V DC 10W isolated
Base ADW 15
Displays	7 segment LED 4.5 digit 10mm.3 x 3mm LED's 2 for relay status, 1 for program and hold indication.
Controls
4 membrane panel keys with tactile feedback. 1 scroll key to view/update parameter. 1 digit select key. 1 digit increment key. 1 reset key. Keypad disable by internal links behind front panel. Hold function by digit select key when in input mode.
Data Retention/Protection
Retention	10 years for set up values, minimum of 100,000 write cycles
Protection of Data Function(s)	Watchdog timer giving repeat auto resets. Impending power detection and hold off. Keypad security and time out.
Physical
Case Material	Grey Noryl, flame retardant
Environmental
Storage temperature	-20 to +70ºC
Operating temperature	-10 to 50ºC
Relative humidity	95% maximum non condensing
CE Environmental Approvals	European EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC

Weighing indicator with RS232 or RS485 options provides digital communications (including setup) and can support label or ticket printers.

Documents

Software

Product order options

Please read the following before selecting the options for this product:

ADW15 Base Unit - Standard Input (100ms). Digital Weighing Indicator/Controller comprising 4.5 digit LED Display Microprocessor Module with Auto Zero, Excitation output 10V @ 150mA Password protected.

Starting with the base model ADW15, select the options that you need to configure the device to meet your needs.

Base Unit	Code
Base Unit ADW15	ADW/15
Fast Input Version (10ms)	ADW15/FPT
Outputs	Code
Analogue Output 0-5V	V02
Analogue Output 0-10V	V04
ADW15 Analogue Output +/-10V	V06
Analogue Output 0-1mA	A01
Analogue Output 0-20mA	A02
Analogue Output 4-20mA	A03
Comms	Code
RS485/232 Comms Module	COM 1
Serial Port	S01
Relay	Code
ADW15 1 Relay SPCO on SP1	R01
ADW15 1 Relay DPCO on SP1	R02
ADW15 2 Relay SPCO on SP1 & SP2	R03
Power Supplies	Code
Power Supply 110V AC	W110
Power Supply 240V AC	W240
Power Supply 12/24V DC	W12/24
Mounting	Code
Panel Mount	P
Din Rail Mounting	D
Accessories	Code
Comms Interface RS232 to 20mA	IF25
Junction Box PCB (only) Active	JPA
Junction Box PCB (only) Passive	JPP
Load Cell Active Junction Box	JBA
VisualLink SCADA Software Full Version (Ex Works)	VLA
VisualLink Runtime Key (Ex Works)	VLR
VisualLink Runtime Key USB (Ex Works)	VLRU
VisualLink Runtime Software Key (Ex Works)	VLS
VisualLink SCADA Software Demo	VLD